A machine for separating oil from water, usually used for treating waste water in restaurants. Because of the requirement of environmental protection, the waste water discharged from the marine machinery places in Rivers, lakes and seas must be treated and an oil-water separator is needed. 1. The market prices of oil-water separator products from regular manufacturers range from a few hundred to several thousand, and the quality varies quite widely. There are also some fake and shoddy products. If you buy inferior products for cheap, the final cost may be a whole set of fuel injection nozzle, or even change the engine, so everyone in the purchase of oil-water separator must go to the regular repair station to buy mainstream big brand products. In order to ensure the fuel supply of the whole engine system, the installed oil-water separator model must be larger than the original car's own displacement. 2. Pay attention to the timely drainage do not think installed on the rest secure, oil-water separator below there is a transparent plastic water cup, in the use of oil-water separator must pay attention to the timely discharge of water, if there is too much water, the oil-water separator will not be able to separate oil from water. Automatic drainage function some foreign advanced manufacturers already have automatic water discharge function. The Filter Cup under the oil-water separator has a water level sensor. When the water level reaches a certain value, it will indicate water on the computer display screen above the instrument panel, the oil-water separator will have to be drained. Drainage operation is also very convenient, pull the handbrake after parking, turn off the engine, ignition key to the driving position, press the switch on the dashboard only about 18 seconds to complete drainage. 3. In addition, the cold weather is also easy to make the water under the Water Cup freeze damage, especially in the north, many users in order to prevent the oil-water separator freeze damage, to oil-water separator put on a thick cotton-padded clothes, but for insurance purposes, or suggest the use of electric heating function of oil-water separator. The oil-water separator for food and beverage is mainly suitable for the environment with serious pollution caused by the discharge of oily sewage in China, installed in the outlet of the sewer, to prevent oil and garbage into the sewer device, mainly FRP, stainless steel and other materials. Due to the advanced design (this product and its design are patented at home and abroad) , the oil resistance rate can reach more than 90% . The grease trap can be buried in the ground or on the ground. After the cover of the anti-skid box is opened, the sewage flows into the residue collection room through the inlet, leaving the solid matter, the waste water flows into the grease trap chamber through the lower edge of the separator, a large amount of grease is floating on the surface after gravity separation, and the deoiled waste water flows into the grease trap chamber through the lower edge of the separator, and the grease is separated again from the floating surface layer, the deoiled sewage outlet flows into the clean water sampling room of the unified standard stipulated by the State Environmental Protection Bureau, which is convenient for sampling and discharging through the discharge pipe. The whole grease trap design fine, reasonable, small size, high efficiency, raw materials for stainless steel and FRP. Product Features 1 low price, no consumable wear-and-tear parts, a year-round benefits of investment. No power and power, no operating costs, completely rely on sewage inflow after the self-purification, easy management. Hard material, easy to clean, long life. Prevention of sewer clogging, avoid the breeding of rats and insects caused by rotten grease, odor overflow and unnecessary cleaning work, extend the service life of the sewer. Dining oil-water separator type selection 1, underground buried type conditions: there are underground buried space. Location: As far as possible at the beginning of the drainage branch (pollution source) . Features: Does Not Occupy the use of space, does not affect walking and transportation. Lifting type (general type, fireproof type and special type) conditions: on the second floor and above, use, use the ground to reserve mounting holes. Location: As far as possible in the drainage horizontal branch pipe at all times (source of contamination) . FEATURES: strong installation, can withstand the weight of equipment, and does not affect the use of floor quality and building life. Types: according to the need to be divided into ordinary type, fireproof type and special type. 3. BED type conditions: no underground space, but there is a place for the ground. Location: directly connected to the sink, stove or water table before the drainage branch. 4, large conditions: underground and bed can be placed. Location: The end of the drainage branch. FEATURES: The utility model can be assembled on the construction site, and can be used in the clear water pool and collecting water pool of the underground high-rise building, which improves the sewage quality and prolongs the service life of the submersible pump.
翻译来自彩云小译
